Products

• Outputs: Eight outputs (latching relays, potential-free contacts)
• Electrical rating per output:ac/
  • 347 Vac, 50/60 Hz, 15A , cos phi = 1
  • 277 Vac, 50/60 Hz, 20A , cos phi = 1
  • 1.5 HP @ 120 Vac
  • 3 HP @ 277 Vac
• Control voltage: 1 to 10V (provided by ECG Dynamic ballast)
• Dimmable electronic ballast: Maximum 60 units
• Signal amplifier: Maximum 12 units

• The JB512C23 Switching actuator (relay) is a KNX device with one switching output.
• The device is installed in a 4 x 4 inch junction box.
• The bus is connected via a bus terminal block.
• The actuator electronics are supplied via the bus voltage.
• The JB512C23 can switch resistive loads (e.g. electrical heaters, incandescent lamps, high voltage halogen lamps), inductive loads (e.g. motor, low voltage halogen lamps with intermediate conventional transformers), or capacitive loads (e.g. low voltage halogen lamps with intermediate electronic transformers).

• The JB513C23 Binary Output (relay) is a KNX device with three switching outputs. The device is installed in a 4 x4 inch junction box. The bus is connected via a bus terminal block.
• The actuator electronics are supplied via the bus voltage.
• The JB513C23 can switch resistive loads (e.g. electrical heaters, incandescent lamps, high voltage halogen lamps), inductive loads (e.g. motor, low voltage halogen lamps with intermediate conventional transformers), or capacitive loads (e.g. low voltage halogen lamps with intermediate electronic transformers).
• Each actuator output may be configured independently to provide switching, manual override, forced control, logical gate and status reporting. 

• The JB520C23 solar protection actuator is a KNX device with one relay output.
• The device is installed in a 4 x 4 inch junction box.
• The bus is connected via a bus terminal block. The actuator electronics are supplied via the bus voltage.
• The JB520C23 may be used to control blinds, shutters, awnings, windows, or doors.
• The device is designed to drive (per channel) one AC 120V drive (motor) with electromechanical limit switches or with integrated electronics for disconnection at the limit positions.

•  Their travel times must be manually measured as precisely as possible and configured in the application program.
• Parallel operation of several drives on one channel requires using a special separation relay. If such a separation relay is connected to the output to drive several drives in parallel, then the travel time must be configured manually.
• If the device is configured for automatic detection of the travel time, then parallel operation of several drives with electromechanical limit switches or mixed operation with drives with integrated electronics for disconnection at the limit positions is not permitted.

• Output for switching and dimming resistive, inductive or capacitive loads
• Automatic adjustment to leading edge or trailing edge control, depending on the type of load
• Rated frequency 50...60 Hz
• Electronic protection of the output against overload, short circuit and temperature rise
• Bus-powered electronics
• Integrated bus coupling unit, Bus connection via bus terminal block
• Type of protection: IP 20
• Rated operational voltage AC 120 V

• Protruding wires stranded AWG 12
• A phase connection for an output that is equipped with a relay contact per output as a switching element
• Contact rated operational voltage AC 120 V, AC 230 V, AC 277 V, AC 347 V
• Contact rated operational voltage AC/DC 24 V
• Contact rated current according to DIN EN 60669-1: 16 A / 20 A (resistive load)
• Fluorescent lamp load according to DIN EN 60669-1: 16 AX / 20 AX (200 µF) at AC 230 V
• Bus-powered electronics
• Integrated bus coupling unit
• Bus connection via bus terminal

• The device can be configured with Desigo Room Automation commissioning tool (ABT) or with KNX Engineering Tool Software (ETS).
• Protruding wires stranded AWG 12
• A phase connection for an output that is equipped with a relay contact per output as a switching element
• Contact rated operational voltage AC120 V, AC 230 V, AC 277 V, AC 347 V
• Contact rated operational voltage AC / DC 24 V
• Contact rated current according to DIN EN 60669-1: 16 A / 20 A (resistive load)
• Fluorescent lamp load according to DIN EN 60669-1: 16 AX / 20 AX (200 µF) at AC 230 V
• Bus-powered electronics
• Integrated bus coupling unit
• Bus connection via bus terminal
• Red LED for display of the activation of the addressing mode as well as the operational readiness

Switching actuator with 2 outputs.

Application area

The KNX IO 510.1 secure (2O) is a compact switching actuator with 2 bi-stable relay outputs.

The actuator provides the function for universal outputs including scene control, timer, staircase lightning and to control heating valves (PWM for thermoelectric valve drives).

Two push buttons and three LEDs allow a local operation and a visualization of the device state.

In addition to the output channels the device includes 16 independent functions for logic or timer control.

The device supports KNX Data Security.

KNX LED dimming actuator 4-fold with constant voltage.

Application area

The KNX IO 534 CV (4D) is a compact RGB / RGBW /Tunable White dimming actuator with 4 PWM outputs.

The dimming actuator can be used e.g. for LED panels or stripes with RGB / RGBW / Tunable White configuration or as 4 independent PWM dimmer channels.

Every configuration allows controlling the channel by switching, rel.

Dimming and dimming value.

Several comfort functions are integrated as well, including scenes, slumber fading, staircase light and sequencer.

KNX LED dimming actuator 4-fold with constant current.

Application area

The KNX IO 536 CC (4D) is a compact RGB / RGBW / Tunable White dimming actuator with 4 outputs (constant current).

The dimming actuator can be used e.g. for LED panels or stripes with RGB / RGBW / Tunable White configuration or as 4 independent dimmer channels.

Every configuration allows controlling the channel by switching, rel.

Dimming and dimming value.

Several comfort functions are integrated as well, including scenes, slumber fading, staircase light and sequencer.

KNX TP 4-fold LED dimming actuator, CC or CV

• 12..24 V⎓ / Max. load current: 6 A total, freely distributable PWM dimming actuator (for CV)
• 12..48 V⎓ / Max. configurable load current: 500 mA each channel (channels can be bundled) (for CC)
• RGB, RGBW, Tunable White
• Scene support, sequencer, staircase function, adjustable dimming curve
• Integrated logic and time functions
• Support of KNX Securtity
• Connectors: KNX, plugable screw connectors for IO
• Size (LxWxH): 132 x 46 x 20 mm

Blind/Shutter control with one output of a KNX Multi IO.

• The device may be used for permanent interior installations in dry locations or within distribution boards with DIN rail.

Bi-stable coupling relay for KNX Multi IO.

Application area

The Multi IO Extension Switch 590 serves as a power-saving alternative to commercial standard coupling relays.

The coupling relay is controlled as a mono-stable relay, but uses a bi-stable relay internally, thus reducing the holding current by up to 95%.

The Multi IO Extension Switch 590 has an integrated fuse to protect high-quality equipment.

• Direct Mode Pushbutton: The button with an integrated yellow LED toggles between bus mode and direct mode.
• Brief Press Functionality: Pressing the button briefly activates the green LED for 30 seconds, indicating the last selected module (A to E) and the switching state of the outputs (red LEDs on buttons 1 to 3).
• Switching State Indication: The red LEDs in buttons 1 to 3 show the relay contact status: LED ON = contact closed, LED OFF = contact open.
• Activating Direct Mode: Holding the button for at least 3 seconds turns on the yellow LED, indicating that direct mode is now active.
• Output Control in Direct Mode: In direct mode, each output of the currently selected module can be switched on or off via a pushbutton on the top of the main module, using a toggle function.
• Pushbutton Behavior: Pressing the pushbutton once turns the output on if it's off, and pressing it again turns it off. The red LED on the pushbutton shows the current state.
• Unused Buttons: Pushbuttons 4 to 6 and their LEDs are not utilized in the N 513/11 model.
• Module Selection: To change the output state of a different module, the desired module must be selected by pressing the direct mode pushbutton multiple times.

• Device Type: The switching actuator sub-module N 513/21 is a DIN-rail mounted device in N-system dimensions.
• Relay Outputs: It can switch three groups of electrical consumers independently via its three relay contact outputs.
• Load Monitoring: Each relay output features load current measurement and monitoring (load-check).
• Standalone Operation: The sub-module cannot operate independently and must be connected to a main module.
• Connection Method: It connects via a 6-pole bridging connector to a main module (N 513/11, N 512/11, or N 562/11) or to another sub-module already connected to a main module.
• Power Supply: The sub-module’s electronics are powered by bus voltage through the 6-pole bridging connector.
• Modular Extension: Up to 4 sub-modules can be connected in series to a main module, extending it from 3-fold to 15-fold switching capability.

• The sunblind actuator N 523/04 only works together with the application program 25 A4 Venetian blind actuator 981201.
• The Engineering Tool Software (ETS) up from ETS2 V1.3 is required for the parameterisation and for loading the application program.
• This is structured so that there is sufficient basic functionality available in the supplied state for simple applications in combination with 11 basic communication ob-jects: the always available object "Status Direct mode", an alarm object that influences all channels, an object "Blockade" that also influences all channels and the two 1-bit command objects per channel enabling a blind to be moved into the upper or lower final position, to stop the drive and to open or close the slats stepwise.
• When commissioning the sunblind actuator the following objects can be added per channel, if needed, via the parameter tab "Functions, Objects":

• Rated voltage: AC 120 V
• Rated current: 20 A
• Number of channels: 8
• Dimensions (W x H x D): 144 x 90 x 60 mm
• Dimension width (1 MW = 18 mm): 8 MW

• Power supply: via KNX Bus line, 20VDC
• Rated voltage: 120V AC +10%/-15%, 50/60 Hz
• Rated current:
  • 2-channel: 2x1.3A@cosФ=1.0
  • 1-channel: 1x2.2A@cosФ=1.0
• N-system DIN-rail mounted device, width:4MU(1MU=18mm)
• Load output:
  

  Lamp type	2 channels	1 channel
  Incandescent lamps	150 W	250 W
  Low voltage halogen lamps with magnetic transformers	120 VA	200 VA
  Dimmable LED	<= 50 VA	<=50 VA